Journal of Prevention and Treatment for Stomatological Diseases ›› 2016, Vol. 24 ›› Issue (5): 280-282.doi: 10.12016/j.issn.2096-1456.2016.05.004

Special Issue: 11

• Basic Study • Previous Articles     Next Articles

The influence of the air abrasion on the resin filling microtensile bond strength of deciduous tooth

YAN Zhi-qi,YE Mei(),YAN Xue-min   

  1. Jiangning Maternal and Child Health Hospital, Nanjing 211100, China
  • Received:2015-10-30 Revised:2015-12-20 Online:2016-05-20 Published:2016-05-20
  • Contact: Mei YE


Objective To investigate the influence of the air abrasion on the resin filling microtensile bond strength of deciduous tooth. Methods 24 primary molars were randomly divided into 2 groups. Crown enamel was removed to expose dentin. Superficial occlusal dentin were prepared by air abrasion or high-speed dental bur. Two samples were selected from each group. One of them was directly observed by scanning electron microscope (SEM) and the other was observed by SEM after etching. The rest of samples were restored with the composite resin. Microtensile test was used to examine the microtensile bond strength. Results The microtensile bond strength of air abrasion group was (24.470±3.194) Mpa, which was statistically higher than that of high-speed dental bur group (22.294±2.268) Mpa (P<0.05). The tooth prepared by air abrasion with etching showed the characteristic of "honeycomb" pattern in SEM micrograghs, while the tooth in the control group showed a shallow shape. Conclusion Air abrasion preparation can improve the microtensile bond strength in dentin restorations with the composite resin.

Key words: Air abrasion, Microtensile bond strength, Primary molar, SEM, Composite resin restoration

CLC Number: 

  • R781.05
[1] 章雯, 彭辉, 周毅 , 等. 空气喷磨处理氟斑牙牙釉质对树脂粘结强度的影响[J]. 口腔生物学, 2011,2(2):82-84.
[2] 张进, 李艳君, 康震 , 等. 空气喷砂技术制洞对树脂粘结界面微渗漏的研究[J]. 中国美容医学, 2010,19(9):1366-1367.
[3] 冉萍, 洋思维 . 喷砂技术在口腔正畸托槽粘贴中的应用[J]. 西南军医, 2013,15(6):623-625.
[4] 齐小秋 . 第三次全国口腔健康流行病学调查报告[M]. 北京: 人民卫生出版社, 2008: 202-204.
[5] 韩东超, 王郑军 . 玻璃离子和复合树脂修复乳牙龋齿的疗效[J]. 临床医学, 2013,33(2):99-100.
[6] 李激 . 3种充填方法修复磨牙邻(牙合)面Ⅱ类洞的临床效果[J]. 广东牙病防治, 2013,21(1):23-25.
[7] 许岩, 汪凤, 郑雪飞 , 等. Er:YAG 激光与涡轮机预备乳牙牙本质表面对树脂剪切强度影响的对比研究[J]. 新疆医科大学学报, 2014,37(11):1504-1507.
[8] 王慧民, 汪俊, 陈曦 , 等. 3种不同龋病治疗方法对儿童牙科畏惧症的影响[J]. 口腔医学, 2014,34(5):372-374.
[9] 方玲, 朱艳莉 . 扫描电镜观察不同方法去腐后牙本质玷污层的形态变化[J]. 中国组织工程研究, 2013,17(38):6725-6732.
[10] Katora ME, Jubach T, Palimus MM . Airbrasive etching of the enamel surface[J]. Quintessence Int Dent Dig, 1981,12(9):967-968.
[11] 傅柏平, 林军, 吴求亮 . 空气喷磨对预防性树脂充填微渗漏的影响[J]. 口腔医学, 2001,20(4):176-177.
[12] 吕炳建 . 不同微粒气磨处理牙面对光固化窝沟封闭效果的影响[D]. 河北:河北医科大学, 2013.
[13] Motisuki C, Lima LM, Bronzi ES , et al. The effectiveness of alumina powder on carious dentin removal[J]. Oper Dent, 2006,31(3):371-376.
doi: 10.2341/05-48
[14] Motisuki C, Monti Lima L, Emi Sanabe M , et al. Evaluation of the microtensile bond strength of composite resin restoration in dentin prepared with different sizes of aluminum oxide particles, using the air abrasion system[J]. Minerva Stomatol, 2006,55(11/12):611-618.
[15] 刘艳丽 . 空气喷砂去龋制洞的实验研究及临床应用[D]. 西安:第四军医大学, 2002: 30-35.
[16] 张培林 . 牙科恐惧症的原因分析及对策[J]. 临床合理用药, 2012,11(32):97.
[17] 王晖, 严加林, 吕敏 . 儿童牙科畏惧症的原因及其诱发因素研究进展[J]. 临床口腔医学, 2014,30(5):318-319.
[1] DONG Limin,LI Bing,WU Xiao,NIU Jianhua. Evaluation of resin inlay restoration after root canal therapy for deciduous molars [J]. Journal of Prevention and Treatment for Stomatological Diseases, 2019, 27(5): 314-317.
[2] Zhendong GONG,Fuchun FANG,Liyan LIU,Buling WU. Clinical effect of semiconductor laser combined with total glucosides of paeony capsules for the treatment of erosive oral lichen planus [J]. Journal of Prevention and Treatment for Stomatological Diseases, 2018, 26(11): 712-716.
[3] Rui-zhi JIA, Dong-mei YANG, Jia-jian SHANG. Clinical study of root canal numbers in maxillary second primary molars [J]. Journal of Prevention and Treatment for Stomatological Diseases, 2017, 25(5): 316-319.
Full text



No Suggested Reading articles found!
This work is licensed under a Creative Commons Attribution 3.0 License.